Opel Frontera

since 1992 of release



Fronter's Opel
+ Opel Frontera brand Cars
- Current leaving and service
   Schedule of routine maintenance
   Current leaving
   Information on control
   Check of levels of liquids
   Check of a condition of tires and pressure in them
   Replacement of impellent oil and oil filter
   Check of level of liquid of system of hydrostrengthening of a wheel
   Rotation of wheels
   Check of a condition and replacement of hoses of an impellent compartment
   Condition check, adjustment of a tension and replacement of a driving belt (only for engines with tension adjustment)
   Check and adjustment of turns of idling of the engine and level WITH
   Check of a condition of the battery, care of it and charging
   Check and replacement of spark plugs
   Check and replacement of candle VV of wires, covers and distributor begunka
   Check of level of oil in a manual box of gear shifting and a transfer case
   Check of level of lubricant liquid of differential of forward and back bridges
   Check of fuel system
   Check of functioning of system of cooling
   Check of a condition of system of production of the fulfilled gases
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts of forward wheels
   Make check of brake system and replacement of brake liquid with the subsequent pumping
   Check of a condition and replacement of brushes of screen wipers
   Filling of a cooler of system of cooling
   Replacement of the fuel filter
   Replacement of the RKPP transmission oil and transfer case
   Replacement of lubricant liquid of differential of forward and back bridges
   Replacement of a distributive belt of the engine
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Manual box of gear shifting
+ Driveshafts, main transfer
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Governing bodies and operation
+ electric equipment Schemes




Check of levels of liquids

GENERAL INFORMATION


Remark

Below procedures of check of level the liquids made through each 400 km of run or weekly are described. The description of other checks of levels of liquid can be found further in the Sections devoted to specific procedures of service. Irrespective of check intervals according to the schedule do not allow, that liquid followed under the car, such leaks indicate malfunction which it is necessary to eliminate immediately.


Liquids are the integral component of systems of greasing, cooling, brake and systems of washing of a windscreen. In view of a gradual expense and/or pollution of liquids in the course of normal operation of the car, it is necessary to replace them periodically. Familiarize with the Section “Types and volumes of applied greasings and liquids” in Specifications before starting to доливу liquids in any of the listed components. Remark: At any check of level of liquid the car should stand on an equal surface.

Impellent oil

PERFORMANCE ORDER
1. Check of level of impellent oil is made by means of measuring щупа, the engine located on one side. Shchup passes through a metal tube down, reaching a bottom of the pallet of a case of the engine.
2. Measurement of level of impellent oil is made before start of the engine or not less than through 15 mines after its switching off.
Recommendations

If to start measurement of level of impellent oil right after engine switching off, the part of oil remains in the top part of the engine that will essentially be reflected in accuracy of indications щупа.


3. Take щуп and dry wipe its edge pure rags or a paper towel. Enter щуп up to the end back and again take it. The height of the site of an edge moistened with oil will correspond to oil level in the engine. This level should be between two labels on щупе.
4. Lifting of level of oil from the minimum label on щупе to maximum needs one liter of oil. Level of oil should remain between two labels, it is desirable at level or is close from top of them - if it not so, add oils to the top label. Do not allow level falling below the minimum label since oil starvation can lead to engine damage. On the other hand, engine overflow by oil (having added above the maximum mark) can be at the bottom of a zamaslivaniye of spark plugs, leakages of oil or failure of epiploons.
5. To add oils, unscrew a cover of a mouth of the gulf, located on a cover of a head of cylinders. After долива some oil wait some minutes that level of oil was stabilized, then pull out щуп and again check level. If it is required, add still oils. Close a cover of a mouth and tighten her hand.
Viscosity of impellent oil
And - seasonal oil
In - all-weather oil
6. Check of level of oil is important preventive procedure. Continuous falling of level of oil indicates or existence of its leaks through the damaged epiploons or weakened connections, or on its burning out (internal leaks through worn-out piston rings or via directing plugs of valves). Besides, it is necessary to pay attention and to a condition of the oil. If oil has dairy color or in its structure it is possible to notice water drops, it indicates possible violation of tightness of laying of a head of cylinders or crack existence in a head or the block of cylinders. In this case the engine should be repaired immediately. Each time at measurement of level of oil before edge rubbing щупа carry out on it big and index hand fingers. If will be thus found stuck on щуп particles of dirt or metal particles, oil it is necessary to replace (see. Section Replacement of impellent oil and oil filter).

Engine cooler

Prevention

Do not allow antifreeze hit on your skin or on the painted surfaces of the car. If it nevertheless occurred, immediately wash away antifreeze a plentiful quantity of water. Antifreeze is extremely toxic in a case hit in an organism. Never leave it without supervision in the open container or spilled on a floor; or animals its sweet smell can involve children and they can drink it. Agree with local authorities about destruction of the used antifreeze.


PERFORMANCE ORDER
1. All cars considered in this Management, are equipped with cooling system with superfluous pressure of compensatory type. The white plastic broad tank (or the cooler tank) is located in an impellent compartment and connected by a hose to a radiator. In process of an engine warming up in the course of its work the extending cooler fills a tank. When cooling engine the cooler automatically arrives back in cooling system that provides maintenance of constant value of its level.
2. Check of level of a cooler in the tank should be made regularly. Add 40 %/60 %-nuyu an antifreeze mix on a basis этиленгликоля with water.
Prevention

Do not uncover a jellied mouth of a broad tank or a radiator cover for check of level of a cooler before complete cooling of the engine! Level in the tank fluctuates depending on engine temperature. When the engine cold, level of a cooler should be higher than "LOW" label on the tank. In process of engine heating level should come nearer to “FULL” label. If it not so, let's to the engine cool down and then uncover the tank.


The broad tank (the cooler tank) is located in a lateral part of an impellent compartment - uncover and add a cooler.
3. Banish the car and again measure cooler level. If to the necessary level it is required to add only small amount of a cooler, for this purpose it is possible to use pure water. However frequent additions of water will dilute antifreeze. To provide a normal ratio of antifreeze and water, always add to the necessary level a demanded mix.
4. If level of a cooler falls regularly, in system leak existence is possible. Examine a radiator, hoses, a cover of a mouth, a stopper plum and the water pump (see. Section Check of functioning of system of cooling). If any leaks it is not revealed, make check of tightness of a cover of a broad tank and a radiator in dealer office of the OPEL service.
5. If you need to uncover, wait, while the engine completely will cool down, then wrap up a piece of thick rags round a cover of t unscrew it to the first emphasis. If thus from under a cover steam or a cooler starts to escape, let's to the engine cool down a little more, and only then uncover.
6. It is necessary to check a cooler condition also. It should be rather pure. If liquid has brown or rusty color, it it is necessary to merge, wash out system and to fill it with a new mix. Even if the cooler looks normally, inhibitors of corrosion entering into its structure lose over time the efficiency therefore it is necessary to replace it through certain periods.

Brake liquid and coupling liquid

Prevention

Brake liquid can harm your eyes and damage the painted surfaces of the car therefore be extremely careful at the treatment of her. Do not use brake liquid which long time stood opened or to which is more than one has some. Brake liquid has property to absorb moisture from air that can lead to dangerous loss of efficiency of brake system. Use only the recommended type of brake liquid. Mixing of various types of liquid (such as and DOT 5) can lead DOT 3 or 4 to refusal of brake system.


PERFORMANCE ORDER
1. The main cylinder of brake system is established in a back left corner of an impellent compartment.
2. To check level of liquid of coupling, look at the translucent tank. Level should be near a ledge on the tank. If it is lower, uncover and add the recommended liquid.
3. Level of brake liquid also is checked visually, on labels on the plastic tank established on the main cylinder. Level of liquid should be between “MAX” and “MIN” labels. If level is lower admissible, at first wipe top of the tank and a cover pure rags to prevent dirt hit in system after cover removal. Add to the necessary level the recommended liquid, but do not pour.
4. While the tank cover is removed, check liquid and the tank of the main cylinder on existence of pollution. If at it there are particles of a rust, dirt or a water drop, liquid from system it is necessary to merge and fill in the new.
5. After долива the tank to the necessary level make sure that the cover is established exactly, in order to avoid leakages of liquid and/or dirt hit.
6. Liquid level in the main cylinder will fall slightly as a result of wear process of frictional overlays of brake shoes. There is no need to add it until level remains near “MIN” label; it will rise after replacement of slips. Very low level can indicate wear of brake shoes. Check them on wear existence (see. Make check of brake system and replacement of brake liquid with the subsequent pumping).
7. If level of brake liquid constantly falls, immediately check all system on existence of leaks. Survey brake lines, hoses and shtutserny connections, together with supports, wheel cylinders and the main cylinder (see. The section Make check of brake system and replacement of brake liquid with the subsequent pumping).
8. If at check of level of liquid one or both of the tank will appear empty or nearly empty, the brake system or system of coupling should be checked on existence of leaks and is pumped over (see. Heads Coupling and Brake system).

Liquid of a washer of glasses and headlights

PERFORMANCE ORDER
1. Liquid for washing of glasses is in the plastic tank in an impellent compartment.
2. In areas with a temperate climate it is possible to fill system with usual water, but the tank should be filled no more, than on two thirds that there was a free space on a case of expansion of water when freezing. In areas with cold climatic conditions it is necessary to use special antifreeze for system of washing of the windscreen, reducing a freezing point of liquid which can be got in any shop of automobile accessories. Usually it is on sale in the concentrated or ready look. If you got the concentrated antifreeze, mix it with water according to the instruction of the producer on packing.

Prevention

Do not use antifreeze of system of cooling - it will damage the painted surfaces of the car.