|
Opel Fronterasince 1992 of release |
|
Fronter's Opel + Opel Frontera brand Cars + Current leaving and service + Engine + cooling and heating Systems + Power supply system and release + engine Electric equipment + Coupling + Manual box of gear shifting + Driveshafts, main transfer + Brake system + Suspension bracket and steering + Body + Onboard electric equipment - Governing bodies and operation Control panel Locks, anticreeping adaptations and body equipment Knots and systems of safety of the driver and passengers Switches of management of lighting and alarm devices Management of functioning of screen wipers/washers Adjustment of provision of rear-view mirrors, door glasses and top hatch Management of giving of an air stream of heating and salon ventilation Driving Car filling by fuel + electric equipment Schemes |
Management of giving of an air stream of heating and salon ventilation
CONTROL PANEL Demanded air temperature in salon of the car is reached for very short time by mixing of cold and hot air streams. Engine turns practically do not influence efficiency of functioning of system. Parameters of an air stream are defined by speed of movement of the car and a choice of a high-speed mode of rotation of the fan of a heater. Need for turning on of the fan arises only at low speeds of movement. The fence of external air in salon is carried out through an air inlet located directly ahead of a windscreen of the car - watch that the air inlet lattice not замусоривалась and was not hammered by snow. CONTROL LEVER AIR INLET
Transfer of the lever to situation (2) switches an air inlet zaslonka to absorption in salon through system of ventilation of external air. At transfer of the lever to situation (1) the closed mode of air circulation supported at the expense of rotation of a krylchatka of the fan of a heater joins - long stay of system in a mode of the closed circulation can lead to a zapotevaniye of glasses therefore whenever possible it is necessary to slightly open a window rather, having opened access of external air. CONTROL LEVER FAN Intensity of supply of air in system of ventilation can be raised at the expense of turning on of the 4-speed fan of a heater.
At lever installation in the situation OFF the fan is disconnected. Situation 1 corresponds to a low-high-speed mode of rotation of the fan; situation 2 is intermediate between modes of low and average speeds of rotation; situation 3 corresponds to an average mode between medium-rate and high-speed; and at last, transfer of the lever to situation 4 switches the fan in a high-speed mode. Remark Functioning of the fan possibly only at the working engine. LEVER OF THE CHOICE OF THE TEMPERATURE MODE
Lever moving towards an inscription of "NOTES" (Hotly) leads to air temperature increase, towards "COLD" - to decrease. CONTROL LEVER AIR DISTRIBUTOR
At lever installation in situation (5) air moves on having blown in a windscreen; the choice of situation (4) carries out supply of air at the same time on having blown in glasses in foot wells; at transfer of the lever to situation (3) air starts to move only in foot wells; situation (2) corresponds to a mode of supply of air both in the top part of salon, and in foot wells; at a choice of situation (1) air moves only in the top part of salon. VENTILATING NOZZLES
Central ventilating nozzles These nozzles are located in the central part of the dashboard of the car directly over the control panel of systems of heating / ventilation (15 on an illustration the Arrangement of components and governing bodies auxiliary systems of the panel of devices / the bottom console) and serve for giving in the top part of salon cold, or warmed-up air, depending on a choice of a temperature mode. Intensity of supply of air can be increased at the expense of turning on of the fan of a heater. By change of provision of a jalousie of lattices snuffled the direction of a stream it can be corrected depending on desire of the driver or the forward passenger. Lateral ventilating nozzles At will of the driver or the forward passenger an air stream from located along the edges of the dashboard snuffled (1 on an illustration the Arrangement of components and governing bodies auxiliary systems of the panel of devices / the bottom console) can be sent both to the central part of salon, and on having blown in door glasses and panels for creation of a layer of warm air along them in a cold season. For change of the direction of a stream it is necessary to turn a jalousie of a lattice of a nozzle as appropriate. Nozzles обдува door windows These nozzles are located also on each side dashboards, but above the lateral ventilating snuffled (2 on an illustration the Arrangement of components and governing bodies auxiliary systems of the panel of devices / the bottom console) and provide additional having blown in glasses of forward doors of the car, mainly around placement of rear-view mirrors. Nozzle of ventilation of salon of knee level The nozzle is intended for обдува knees of the driver and located in the lower part of the dashboard under a steering wheel (24 on an illustration the Arrangement of components and governing bodies auxiliary systems of the panel of devices / the bottom console). Possibility of adjustment of the direction of a stream of air from the real nozzle in the vertical plane at the expense of turn of a jalousie of a lattice is provided. Intensity of a stream can be increased at the expense of turning on of the fan of a heater. Nozzles of supply of air in foot wells Nozzles are located in the basis of assembly of a heater. Intensity of a stream can be increased at the expense of turning on of the fan. CHOICE OF MODES OF FUNCTIONING OF SYSTEMS OF HEATING / VENTILATION OF SALON Inclusion of a mode of ventilation of salon Choice of a mode of heating of salon Intensity of supply of air is defined by a choice of speed of rotation of the fan (the bottom right lever on control panels). The demanded temperature mode is set by the left bottom lever on the control panel. Comfortableness of climate in salon considerably is defined by a choice of the direction of supply of warm air.
Mode inclusion obduva/heating of glasses
AIR CENTRAL AIR If the car is equipped with air central air, functioning of the last becomes possible only at the working engine and included on any of high-speed modes the heater fan. The design of the conditioner defines need of its operation together with systems of heating and ventilation of salon of the car. Air conditioning allows to achieve passengers of climatic conditions optimum for health in car salon under any weather conditions outside.
Switching off of system is made by repeated pressing of the same button. At turning on of the conditioner of air fuel consumption therefore it is not necessary to be fond of its use without special need a little raises. Heating of back glass Remark Heating of back glass is possible only at the included ignition.
The element of a heater of back glass is the power-intensive consumer, and therefore it should be disconnected at once as soon as glass will gain due transparency. Electroheating of forward seats Inclusion of electroheating of each of forward seats of the car (if that is provided) is carried out by the separate button. Both buttons are located on the parties of the central console of the car. At heater inclusion in the corresponding button the control lamp lights up. |
|