Fronter's Opel
+ Opel Frontera brand Cars
+ Current leaving and service
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Manual box of gear shifting
+ Driveshafts, main transfer
+ Brake system
- Suspension bracket and steering
+ Suspension bracket of forward wheels and forward bridge
+ Suspension bracket of back wheels and back bridge
- Steering with the hydraulic booster
Verifying and adjusting works on a steering
Works on a steering drive
Steering wheel and steering column
Steering mechanism
Pump of the hydraulic booster
Safety cushion
+ Body
+ Onboard electric equipment
+ Governing bodies and operation
+ electric equipment Schemes
|
Works on a steering drive
For separation of spherical hinges of a steering drive the special stripper is required. If in the text it is specified "remove the sharovy hinge" that it means that it is necessary to unscrew a nut of fastening of a spherical finger and to take out it by means of a stripper.
REMOVAL AND MAYATNIKY'S INSTALLATION OF THE LEVER
Removal
| PERFORMANCE ORDER |
| |
1. Unscrew a nut and disconnect the pendular lever from an axis on an arm. For this purpose it is possible to use a dvukhzakhvatny stripper (see also removal of a steering soshka). |
| 2. Unscrew four bolts and the nuts of fastening shown on an illustration, and remove an arm of the mayatniky lever from the chassis. |
|
Installation
The pendular lever in sequence is established, to return to removal.
| PERFORMANCE ORDER |
| 1. Bolts of fastening of an arm tighten the moment of 48 Nanometers, a nut of fastening of the mayatniky lever the moment of 130 Nanometers. |
| 2. After installation check a convergence of forward wheels and if necessary adjust (see. Section 2). |
|
STEERING SOSHKA AND PENDULAR LEVER
| PERFORMANCE ORDER |
| 1. Disconnect average steering draft from the mayatniky lever. |
| |
2. Disconnect a steering soshka from the steering mechanism, and the pendular lever from an arm axis. For this purpose the dvukhzakhvatny stripper is applied. |
|
The steering soshka and the pendular lever as follows are established:
| PERFORMANCE ORDER |
| 1. Put on a steering soshka a segment shaft. Thus it is necessary to pay attention to shift of some шлицов of connection. |
| 2. Screw a nut and tighten it the moment of 220 Nanometers. |
| 3. Put on an arm axis a steering soshka and tighten a nut of fastening the moment of 130 Nanometers. |
| 4. Connect to a steering soshka and the pendular lever average draft. |
Prevention
Observe the inhaling moments! The fastening nut the helmsman of a soshka fastens the moment of 110 Nanometers, a nut of the pendular lever the moment of 60 Nanometers.
|
| 5. Zashplintuyte both nuts. |
| 6. Check a convergence of wheels according to indications of section 2. |
|
REPLACEMENT OF EXTERNAL STEERING DRAUGHTS AND TIPS OF STEERING DRAUGHTS
| PERFORMANCE ORDER |
| |
1. Weaken lock-nuts on outer sides of steering draft. The nut with the left carving has marking of "L". The arrangement of nuts is shown on an illustration. |
| 2. Disconnect external steering draft from a steering soshka and from average draft and remove steering draft. |
| 3. Having counted quantity of turns, unscrew tips from steering draft. Write down the received quantity of turns. |
| 4. Disconnect steering draft from a soshka and from the pendular lever and remove steering draft. |
|
External steering drafts and tips in sequence are established, to return to removal. Thus it is necessary to mean the following:
| PERFORMANCE ORDER |
| 1. Attach average bent for to a steering soshka and the pendular lever. The nut of fastening of the pendular lever is tightened by the moment of 60 Nanometers, a nut of fastening of a soshka the moment of 110 Nanometers. Zashplintuyte both nuts. |
| |
2. Screw tips of steering drafts on the number of the turns which has been written down at removal, and measure steering drafts according to an illustration. |
| 3. Connect steering drafts to the left carving with average draft and tighten nuts. |
| 4. Fix a soshka the moment of 110 Nanometers. |
| |
5. Tighten lock-nuts of steering drafts the moment of 120 Nanometers. |
| 6. In summary check a convergence of wheels and if necessary adjust. |
|
|
|