Opel Frontera

since 1992 of release


Fronter's Opel
+ Opel Frontera brand Cars
- Current leaving and service
   Schedule of routine maintenance
   Current leaving
   Information on control
   Check of levels of liquids
   Check of a condition of tires and pressure in them
   Replacement of impellent oil and oil filter
   Check of level of liquid of system of hydrostrengthening of a wheel
   Rotation of wheels
   Check of a condition and replacement of hoses of an impellent compartment
   Condition check, adjustment of a tension and replacement of a driving belt (only for engines with tension adjustment)
   Check and adjustment of turns of idling of the engine and level WITH
   Check of a condition of the battery, care of it and charging
   Check and replacement of spark plugs
   Check and replacement of candle VV of wires, covers and distributor begunka
   Check of level of oil in a manual box of gear shifting and a transfer case
   Check of level of lubricant liquid of differential of forward and back bridges
   Check of fuel system
   Check of functioning of system of cooling
   Check of a condition of system of production of the fulfilled gases
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts of forward wheels
   Make check of brake system and replacement of brake liquid with the subsequent pumping
   Check of a condition and replacement of brushes of screen wipers
   Filling of a cooler of system of cooling
   Replacement of the fuel filter
   Replacement of the RKPP transmission oil and transfer case
   Replacement of lubricant liquid of differential of forward and back bridges
   Replacement of a distributive belt of the engine
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Manual box of gear shifting
+ Driveshafts, main transfer
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Governing bodies and operation
+ electric equipment Schemes



Check and replacement of candle VV of wires, covers and distributor begunka
PERFORMANCE ORDER
1. Check of a condition of candle VV of wires should be made regularly through the recommended intervals and each time at replacement of spark plugs.
2. Begin this procedure with external survey of wires at the working engine. In the blacked-out garage (track that indoors there was a good ventilation) start the engine and attentively examine each wire. Try not to touch moving parts of the engine. In the presence of break the wire will spark in a damage place. In this case replace wires, then let's to the engine cool down.
3. Disconnect a negative wire of the battery.
Prevention

Prevention: If the radio receiver of your car is equipped with system of protection against theft, make sure that you gathered the correct code before a battery detachment.

4. In order to avoid confusion at installation check of VV of wires should be made serially.
5. Disconnect VV a wire from a spark plug. Do not pull for a wire, only and I will corrode.
6. Examine an internal part of the socket on existence of corrosion which looks like a white friable powder. Connect a wire with the socket to a spark plug. The socket should hardly a network on a candle. If it is not possible to reach it, again remove a wire and correct flat-nose pliers position of the plug in the socket.
7. Pure rags wipe wires outside on all length, deleting from them the stuck dirt and greasing. After cleaning check a wire on existence of traces прогаров, cracks and other damages. Do not bend a wire under acute angles since it can lead to a conductor fiasco.
8. Disconnect VV a wire from the distributor. Do not forget to pull only for the socket. Check it on existence of corrosion and connect in the same way, as well as a spark plug wire. If necessary replace a distributor wire.
9. Check other wires of spark plugs, and after check make sure that each of them is reliably attached to the distributor and a candle.
10. If candle wires demand replacement, buy the set of the wires which has been specially intended for your model of the engine. Wires of the necessary length enter into sets and with the established sockets. Remove and replace wire VV on one not to allow confusion in an operating procedure of cylinders at their installation.
11a. Weaken screws or open clips, then uncover the distributor. Take away a distributor cover so that it was possible to examine it from within.
11b. Give screws (if they are available) and remove a begunok from a shaft.
11с. In drawing covers of the distributor some of widespread defects to which it is necessary to pay attention at survey (if there are doubts concerning its condition, replace it better) are shown.
11d. Check a cover and a distributor begunok on existence of signs of wear, cracks, coal traces and the worn-out, burned slightly or weakened contacts. At detection of defects replace a cover or a begunok. Usually a cover and a begunok it is accepted to replace each time at replacement of candle wires. At installation of a new cover on one disconnect wire VV from an old cover and connect them to new in just the same order - never disconnect all wires at the same time in order to avoid confusion in an operating procedure of cylinders at their installation.